MCT Flooring All articles
Planning & Timing

Clearance Before Colour: The Doorway Test That Should Come Before Any Floor Sample

MCT Flooring
Clearance Before Colour: The Doorway Test That Should Come Before Any Floor Sample

Photo: measuring door clearance under open door with tape measure flooring sample UK home, via modernartifact.com

Most flooring decisions start with a sample. That's natural — colour and texture are what you see first. But before the sample gets a say, there's a quieter test that decides whether the whole project runs smoothly: the doorway. A new floor doesn't just sit in a room; it rises into it. Every millimetre of board, underlay, adhesive and prep adds up, and the first place that bill usually arrives is under a door.

At MCT Flooring, we've seen lovely boards rejected late in the day because nobody checked the gap. We've also seen doors planed down to paper-thin edges to squeeze a thick floor underneath. Both are avoidable with a short measuring routine run before you order — not after the pallets are on the drive.

Start with the finished floor, not the board

The number that matters is the finished floor height, not the thickness printed on the sample label. That means the whole build-up: the board itself, whatever goes under it, and any prep or backer that has to go down first.

A few common examples make the point. An engineered wood board might be 14mm, plus a 3mm underlay, giving roughly 17mm. A glue-down luxury vinyl tile might be 5mm, but the adhesive and any smoothing compound still count. A tile backer board plus adhesive plus the tile can add considerably more than the tile alone. Even a seemingly slim floor can finish deeper once it's installed properly.

So the first job is to get the actual specified build-up from your fitter or supplier in writing. Not "about 15mm" — the real stack. If the floor is going over a less-than-perfect subfloor, ask whether a levelling compound is likely. That can add another couple of millimetres, and those millimetres have a habit of turning up under the tightest door in the house.

The doorway is the first reality check

Before you fall for a sample, walk the rooms with a tape measure and a notepad. At every door, measure the gap between the existing floor and the underside of the door leaf. Take three readings: hinge side, middle and latch side. Old doors are rarely level, and older UK homes are rarely square, so one reading can flatter you.

Then compare that gap with your proposed build-up. If the floor is 17mm and the tightest gap is 18mm, you're not necessarily fine. Doors need clearance to swing, and a floor that just scrapes is a floor that will mark, squeak or catch on a rug. If the gap is smaller than the build-up, the door will need trimming — and that's a joinery job with a limit. Hollow doors can only lose so much material, and period solid doors deserve more respect than a rushed plane-down.

A useful trick is to cut a scrap batten or piece of ply to the exact build-up depth, slide it under the door and open and close the door over it. It's not a perfect simulation, but it tells you quickly whether you're in comfortable territory or heading for a nasty surprise.

Five numbers to write down before you order

A simple pre-order sheet keeps everyone honest. Note the existing floor-to-door gap at every doorway. Note the proposed finished build-up. Note the door leaf thickness, because your joiner will want it. Note the threshold or transition details — especially where a new floor meets an old one, or where two different materials meet. And note the gaps around kitchen appliances, built-in cupboards and utility spaces.

That last one catches people out. A thicker floor can leave a dishwasher tight under the worktop, a fridge freezer struggling to roll back, or a cupboard door catching on the new surface. It's much easier to adjust the specification than to argue with a plinth later.

Where floor height quietly eats the budget

Door trimming is the obvious cost, but it's not the only one. A thicker floor can change the skirting line: either the skirting needs removing and refitting, or the new floor covers the bottom edge and makes the skirting look shallower. Thresholds may need replacing or adapting. Radiator pipes, door stops and built-in furniture can all become part of the conversation.

In older properties — Victorian terraces, 1930s semis, cottages with floors that have settled — the variation from one doorway to the next can be significant. Don't assume that because the front room door has plenty of clearance, the back bedroom will be the same. Measure each one.

A calm routine beats a rushed compromise

Choose your shortlist, then get the build-up confirmed. Measure every doorway. Check the transitions. Check appliance and cupboard gaps. Decide whether you're willing to pay for joinery work or whether a thinner floor is the smarter choice. Only then should the sample get the final vote.

None of this takes long. It's a ten-minute walk-round with a tape and a scrap of timber, and it protects both the look of the floor and the mechanics of the room. At MCT Flooring, we'd rather have that conversation before the order than after the first door starts catching. A floor should feel like a finished decision — not the start of a joinery queue.

All Articles

Related Articles

The Spare-Box Rule: Ordering Flooring for Real Rooms, Not Perfect Maths

The Spare-Box Rule: Ordering Flooring for Real Rooms, Not Perfect Maths

Thirteen Steps, One Order: Sorting the Staircase Before the Flooring Lands

Thirteen Steps, One Order: Sorting the Staircase Before the Flooring Lands

Turning a Cold Concrete Box into a Workspace: Floor Decisions for a Garage Conversion

Turning a Cold Concrete Box into a Workspace: Floor Decisions for a Garage Conversion